Pioneers in the industry, we offer jbl vrx932la -12 in. two-way line array loudspeaker, jbl vrx932lap 12 in. two-way powered line array loudspeaker system, jbl control 23-1 ultra-compact indoor/outdoor background/foreground speaker, yamaha ns-c444 2-way center channel speaker, jbl c2pm control 2p (host only) and dynatech - hp-8a+ active 2way from India.
Get Latest Price
| Power | 800 W |
| Connectivity | Wired |
| Speaker Channel | Single |
| Color | Black |
| Dimensions (H x W x D) | 343mm x 597mm x 376mm (13.5in x 23.5in x 14.8in) |
| Max Rated Spl | 130db |
| Power Rating | 800 W / 1600 W / 3200 W |
| Frequency Range (-10dB) | 57 Hz - 20 kHz |
| Dimensions (H x W x D) | 343mm x 597mm x 376mm (13.5in x 23.5in x 14.8in) |
| Frequency Response (±3 dB) | 75 Hz - 20 Hz |
| Coverage Pattern | 100 x 15 nominal |
| Crossover Modes | Bi-amp / passive, externally switchable |
| Crossover Frequency | 132 dB SPL peak 1.2 kHz |
| Maximum SPL (1m) | 130 dB SPL peak (passive mode) LF: 130 dB HF: 139 dB |
| Sensitivity | Passive: 95 dB SPL Bi-amp LF: 95 dB SPL Bi-amp HF: 114 dB SPL |
| LF Driver | 1 x JBL 2262H 305 mm (12 in) Differential Drive® woofer with neodymium magnet, dual voice-coils, and dual magnetic gaps. |
| HF Driver | 3 x JBL 2408J, 38 mm (1.5 in) voice-coil, neodymium compression driver |
| Nominal Impedance | Passive = 8 ohm Bi-amp LF = 8 ohm Bi-amp HF = 8 ohm |
| Active Tunings | Tunings available |
| Enclosure | 18 mm, 11-ply birch plywood |
Get Latest Price
| Power | 1800 W |
| Connectivity | Wired |
| Speaker Channel | SINGLE |
| Color | Black |
| Dimensions (H x W x D) | 349 mm x 597 mm x 444 mm(13.75 in x 23.5 in x 17.5 in) |
| Max Rated Spl | 136 dB SPL |
| Impedance | NA - amplification is integrated |
| Freq.Response | 75 Hz - 20 kHz (+/-3db) |
| Power Rating | 1750 Watts Peak875 Watts Continuous |
| Frequency Range (-10dB) | 57 Hz - 20 kHz |
| Dimensions (H x W x D) | 349 mm x 597 mm x 444 mm(13.75 in x 23.5 in x 17.5 in) |
| Frequency Response | 75 Hz - 20 kHz (+/-3db) |
| Maximum SPL (1m) | 136 dB SPL |
| Coverage Pattern | 100 x 15 nominal |
| DPC-2 Output as (Continuous IED shaped pink noise into rated load impedance) | LF: 750 Watts, HF: 125 Watts |
| DPC-2 Output Section | LF: Dual-Bridged Technology™, Class D |
| Inputs | XLR with loop through |
| LF Driver | 1 x JBL 2262FF 305 mm (12 in) neodymium magnet |
| HF Driver | 3 x JBL 2408J, 38 mm (1.5 in) |
| User Controls | Input Attenuator (0-16 dB) |
| Signal Processings | DSP based, resident in Input Module |
| AC Power Operating Range | 90-132 VAC or 216-264 VAC, 50/60 Hz |
| AC Input Connector | Neutrik PowerCon (NAC 3MPA) |
| AC Loop Through Connector | Neutrik PowerCon (NAC 3MPB) |
| AC Current Requirements | 6A per system at 120V, 3A per system at 240V |
| Enclosure | 25/15 mm, 11-ply birch plywood |
| Suspension / Mounting | Optional VRX-AF line array frame kit, 10mm forged eyebolts or internal dual angle 36mm pole mount cup for pole or tripod mounting |
| Finish | Black DuraFlex™ finish |
| Grille | Powder coated, black, 16-gauge perforated steel with with acoustically transparent foam |
| Net Weight (each) | 24 kg (52 lb) |
| Optional Accessories | VRX-AF: Suspension array frame |
| Outputs | 1 x XLR |
| System Type | Constant Curvature 12" Two-Way Powered Line Array System |
| Nominal Impedance | NA - amplification is integrated |
Get Latest Price
| Connectivity | Wired |
| Color | Black |
| Power | 100W Continuous Program (2 hrs)50 W (200W peak), Continuous Pink Noise (2 hrs) 40 W (160W peak) Cont |
| Dimensions (W x D x H) | 200 x 141 x 111 mm (7.9 x 5.6 x 4.4 in); 141 mm (5.6 in) deep total when mounted on InvisiBall wall- |
| Impedance | 8 ohms (THRU setting) |
| Sensitivity | 86 dB, 1W/1m (ave. 100 Hz - 10 kHz) |
| Freq.Response | 95 Hz - 19 kHz |
| Weight | 1.8 kg (4.0 lbs) |
| Frequency Range (-10dB) | 70 Hz to 20 kHz |
| Frequency Response (±3 dB) | 95 Hz - 19 kHz |
| Power Rating | 100W Continuous Program (2 hrs)50 W (200W peak), Continuous Pink Noise (2 hrs) 40 W (160W peak) Continuous Pink Noise (100 hrs) |
| Maximum Input Voltage | 17.2 V RMS (2 hrs), 34.4 V peak |
| Maximum SPL (1m) | 103 dB ave. Continuous Pink Noise (109 dB peak) |
| Sensitivity | 86 dB, 1W/1m (ave. 100 Hz – 10 kHz) |
| Coverage Angle | 100°H x 100°V |
| Directivity Factor (Q) | 5.8 (averaged 1kHz – 16kHz) |
| Directivity Index (DI) | 7.2 dB (averaged 1kHz – 16kHz) |
| Impedance | 8 ohms (THRU setting) |
| Crossover Type | 2nd order low-pass, 2nd order high-pass |
| Transformer Taps | 70V: 15W, 7.5W, 3.7W, 1.8W100V: 15W, 7.5W, 3.7W Insertion Loss <0.43 dB at any tap settingThru Setting: 8Ω nominal |
| Recommended ProtectiveHigh-Pass | 70 Hz high-pass (24 dB/oct) (for 8Ω operation and for all 70V/100V taps settings). |
| Drivers | LF: 76 mm (3.0 in), woven-fiberglass cone with pure butyl rubber surround with Weather-Edge frame protection, high-temp Kapton™ voice coil former, high-temp voice coil wire, optimized cone geometry, linear suspension spider, and FEA optimized motor structure. HF: 13 mm (0.5 in) PEI diaphragm, low-viscosity ferro-magnetic fluid, and lightweight Kapton™ voice coil former. |
| Enclosure | High Impact Polystyrene (HIPS), painted with highly-UV resistant paint on white (-WH) version for maximum UV fade resistance. |
| Grille | Highly zinc-plated, finished in durable TGIC polyester powdercoating. MTC-23WMG-1 (&-WH) available with WeatherMax™ multi-layer foam and tight-weave mesh vapor barrier backing. |
| Mounting Hardware | InvisiBall™ wall-mounting system included. Two 6 mm attachment points (on top and bottom) for optional MTC-23UB-1 (&-WH) U-bracket. Secondary safety attachment loop point on back panel. |
| Outdoor Capability | IP-44 per IEC529 (IP-55 when installed with the optional MTC-23WMG-1 WeatherMax™ grille and either MTC-PC2 or MTC-PC3 panel cover.) Exceeds MilSpec 810 for humidity, salt-spray, temperature & UV. Passes MilStd-202F for salt spray and ASTM G85 for acid-air plus salt spray. Optional MTC-23WMG-1 WeatherMax™ grille for breaking up driving rain and for especially difficult environments. |
| Input Connectors | Screw-down terminal strip, zinc-plated copper based, nickel-plated metal screws and washers. Accepts up to 9 mm outside 4 mm inside open lugs (#6, #8, or #10 lug), plus bare wire (up to 12 AWG / 2.5 mm2). Optional MTC-PC2 and MTC-PC3 protective panel covers available to provide sealed entrance for additional weather protection. |
| Agency Rating | ROHS-compliant; Transformer UL Recognized per UL1876 |
| Colors | Black (RAL9004) or white (-WH, RAL9016) |
| Dimensions (H x W x D) | 200 x 141 x 111 mm (7.9 x 5.6 x 4.4 in); 141 mm (5.6 in) deep total when mounted on InvisiBall wall-mount bracket. |
| Net Weight | 1.8 kg (4.0 lbs) |
Get Latest Price
| Connectivity | Wired |
| Power | 100 W RMS 250 W Peak |
| Speaker Channel | single |
| Color | Black |
| Dimensions (H x W x D) | 20.3 x 7.5 x 8.4" / 51.6 x 19.1 x 21.3 cm |
| Impedance | 6 Ohms |
| Sensitivity | 89 dB |
| Freq.Response | 55 Hz to 35 kHz |
| Weight | 16.1 lb / 7.3 kg |
| Speaker Configuration | 2-Way |
| Power Handling | 100 W RMS 250 W Peak |
| Drivers | 1 x 1" / 25.4 mm Aluminum Dome Tweeter 2 x 5" / 127 mm Polymer-Injected Mica Cone Woofer |
| Frequency Response | 55 Hz to 35 kHz |
| Inputs/Outputs | Screw Terminal |
| Speaker Configuration | 2-Way |
| Power Handling | 100 W RMS 250 W Peak |
| Bi-Amp Capability | No |
| Drivers | 1 x 1" / 25.4 mm Aluminum Dome Tweeter 2 x 5" / 127 mm Polymer-Injected Mica Cone Woofer |
| Enclosure Type | Sealed |
| Ports | No |
| Frequency Response | 55 Hz to 35 kHz |
| Impedance | 6 Ohms |
| Magnetic Shielding | Yes |
| Inputs/Outputs | Screw Terminal |
| Crossover | 3 kHz |
| Sensitivity | 89 dB |
| Environmental Protection | No |
| Placement & Mounting Options | Tabletop/Bookshelf |
| Floor Contacts | Silicone Pad |
| Grille | Cloth (Removable) |
| Dimensions | 20.3 x 7.5 x 8.4" / 51.6 x 19.1 x 21.3 cm |
| Weight | 16.1 lb / 7.3 kg |
| Package Weight | 17.95 lb |
| Box Dimensions (LxWxH) | 23.5 x 12 x 11.5" |
Get Latest Price
| Connectivity | Wired |
| Power | 19 VDC / 3.42 A - use only supplied power supply |
| Dimensions (W x D x H) | 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in) |
| Sensitivity | +4 dBu XLR 1/4"; 0 dBu RCA |
| Freq.Response | 80 Hz - 20 kHz |
| Weight | 2.6 kg (5.5 lb) |
| Drivers | LF: 135 mm (5.25 in) low frequency loudspeaker HF: 19 mm (.75 in) Polycarbonate dome tweeter |
| Frequency Range | 80 Hz - 20 kHz |
| Amplifier Power Rating | 35 Watts |
| Maximum SPL (1m) | 111 dB |
| Crossover Frequency | 4.2 kHz |
| Input Sensitivity | +4 dBu XLR 1/4"; 0 dBu RCA |
| Input Connectors | Balanced Neutrik®* Combo XLR 1/4" TRS; Unbalanced RCA |
| Power Requirements | 19 VDC / 3.42 A - use only supplied power supply |
| Headphone Jack | 3.5 mm (1/8") |
| Dimensions (H x W x D) | 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in) |
| Net Weight (each) | 2.6 kg (5.5 lb) |
| Grille | Zinc-plated steel |
| Mounting Hardware | Optional |
| Included Accessories | Speaker wire, power supply, 2 snap-on pedestals. |
| Optional Accessories | MTC-2P Mounting Kit (2 brackets, power supply holder) |
|
* Neutrik and the names of Neutrik products referenced herein are either trademarks and /or service marks |
|
| LF Driver | 5.25in (135 mm) |
| LF Driver Power Handling | 35 Watts per channel |
| Frequency Response (±3 dB) | 100 Hz – 18 kHz |
| Maximum Peak SPL | 111 dB |
| Enclosure | Polypropylene Structural Foam |
| Coverage Angle | 120°H x120°V |
Get Latest Price
| Connectivity | Wired |
| Power | 150W (RMS) |
| Color | Black |
| Dimensions (H x W x D) | 33 X 34 X 50 |
| Vertical Coverage Angle | 90 Degree X 60 Degree |
| Material | Moulded Polypropylene Enclosure |
| High Frequency Driver | 1" Exit, 1" VC, Ferrite |
| Freq.Response | 65Hz - 18 kHz |
| Voice Coil Diameter | 8", 1.5" VC, Ferrite Magnet |
| Magnet | Ferrite Magnet |
| Weight | 9.5 kgs |
Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value.
Get Latest Price
| Power | Above 150 W |
| Size/Dimension | 207 x 383 x 329; 8-1/8" x 15-1/8" x 13" |
| Channel | SINGLE |
| Subwoofer Type | Passive |
| Color | Black |
| Model Name/Number | NS-600A |
| Rated Impedance | 6 ohms |
| Weight | 9.9 kg (21.8 lbs) |
| NS-600A | |
|---|---|
| Specifications | |
| Type | 2 way Bass-Reflex Type |
| Woofers | 13cm (5-1/8") cone type |
| Tweeter | 3cm (1-1/4") dome type |
| Frequency Response | 47 Hz-65 kHz (-10 dB), -100 kHz (-30 dB) |
| Nominal Input Power | 40 W |
| Maximum Input Power | 120 W |
| Sensitivity | 85.5 dB |
| Crossover Frequencies | 2.6 kHz |
| Impedance | 6 ohms (minimum 3.6 ohms) |
| Dimensions (W x H x D) | 207 x 383 x 329; 8-1/8" x 15-1/8" x 13" |
| Weight | 9.9 kg (21.8 lbs) |
| Accessories | |
| Accessories | Front Grille x 1, Cushion x 4 |
Get Latest Price
| Connectivity | Wired |
| Speaker Channel | single |
| Color | Black |
| Dimensions (H x W x D) | 419 x 254 x 308mm (16.5" x 10" x 12.1") |
| LF Driver | 203mm (8") |
| HF DRIVER SIZE | 25mm (1") |
| HF DRIVER TYPE | Soft dome |
| Crossover | 1800Hz 4th order acoustic Linkwitz-Riley |
| OK FOR USE NEAR MAGNETICALLY SENSITIVE EQUIPMENT | |
| INPUT SENSITIVITY (-10dBV INPUT) | 92dB / 1m |
| Power Configuration | Bi-amplified |
| HF DRIVER POWER AMP | 56W, Class-D |
| LF Driver Power Handling | 56W, Class-D |
| Frequency Response (±3 dB) | 45Hz – 20kHz |
| Frequency Range (-10dB) | 37Hz – 24kHz |
| LOW FREQUENCY EXTENSION (-10dB) | 37Hz |
| Maximum Continuous SPL | 102dB |
| Maximum Peak SPL | 112dB |
| MAXIMUM PEAK INPUT LEVEL (-10dBV / +4dBu) | +6dBV / +20.3dBu |
| SYSTEM DISTORTION CRITERIA | <10% THD at maximum output with full compressor / limiter engagement |
| ELECTRICAL DISTORTION CRITERIA | 0.2% THD @ 1kHz / 2.83VRMS output; <1% THD @ 1kHz, full rated output |
| Signal to Noise Ratio | 75dBA (A-Weighted), 70dBr (unweighted), relative to 2.83VRMS output |
| Coverage Angle | 120° x 90° |
| Input Connectors | 1 x XLR female, 1 x TRS female, balanced |
| HF TRIM CONTROL | -2dB, 0dB, +2dB |
| BOUNDARY EQ | LF Shelf @ 50Hz: -3dB, -1.5dB, 0dB |
| AC INPUT VOLTAGE | 100 – 240VAC (±10%), 50 / 60Hz |
| ENCLOSURE TYPE | Ported |
| Enclosure | 15mm MDF |
| ENCLOSURE FINISH | Matte black PVC |
| BAFFLE CONSTRUCTION | Injection-molded structural ABS |
| CABINET DIMENSIONS (H x W x D) | 419 x 254 x 308mm (16.5" x 10" x 12.1") |
| DISPLAY CARTON (H x W x D) | 473 x 312 x 358mm (18.6" x 12.3" x 14") |
| SHIPPING CARTON (H x W x D) | 491 x 326 x 372mm (19.3" x 12.8" x 14.6") |
| Net Weight (each) | 8.1 kg (17.87 lbs) |
| SHIPPING GROSS WEIGHT | 9.4 kg (20.73 lbs) |
Get Latest Price
| Connectivity | Wired |
| Power | 300 W / 600 W / 1200 W(Continuous/Program/Peak) |
| Speaker Channel | SINGLE |
| Color | Black |
| Dimensions (H x W x D) | 574 mm x 353 mm x 399 mm (22.6 in x 13.9 in x 15.7 in) |
| Impedance | 8 ohms |
| Sensitivity | 95 dB SPL (1w@1m) |
| Freq.Response | 62 Hz - 19 kHz |
| Weight | 16 kg (35 lbs.) |
| Frequency Range (-10dB) | 50 Hz – 20 kHz |
| Frequency Response (±3 dB) | 62 Hz – 19 kHz |
| Coverage Pattern | 90° x 50° nominal |
| System Sensitivity | 95 dB SPL (1w@1m) |
| Power Rating, Pink Noise | 300 W / 600 W / 1200 W(Continuous/Program/Peak) |
| Maximum SPL (1m) | 126 dB SPL peak |
| Nominal Impedance | 8 ohms |
| Dimensions (H x W x D) | 574 mm x 353 mm x 399 mm (22.6 in x 13.9 in x 15.7 in) |
| Net Weight | 16 kg (35 lbs.) |
| Inputs | Parallel Neutrik® Speakon® NL-2 / ¼" phone combo jacks |
| Enclosure | Duraflex coated plywood |
Get Latest Price
| Power | Below 100 W |
| Size/Dimension | 500 mm (19.7") 343 mm (13.5") (with rubber feet) 454 mm (17.9") |
| Channel | simgle |
| Subwoofer Type | Active |
| Color | Black |
| Weight | 16.5 kg (36.4 lbs) |
| DHR15 | DHR12M |
|---|
| DHR15 | DHR12M | ||
|---|---|---|---|
| General specifications | |||
| Speaker type | 2-way, Bi-amped Powered Speaker, Bass-reflex | 2-way, Bi-amped Powered Speaker, Bass-reflex | |
| Frequency range (-10dB) | 44 Hz - 20 kHz | 55 Hz - 20 kHz | |
| Coverage area | H90゚ x V60゚ | H90゚ x V90゚ | |
| Crossover | 1.8 kHz: FIR-X tuning™ (linear phase FIR filter) | 1.8 kHz: FIR-X tuning™ (linear phase FIR filter) | |
| Maximum Output Level (Measured peak, IEC noise@1m) | 131 dB SPL | 129 dB SPL | |
| Components | LF | Diameter: 15" cone, Voice Coil: 2.5", Magnet: Ferrite | Diameter: 12" cone, Voice Coil: 2.5", Magnet: Ferrite |
| HF | Diaphragm: 1.4", Type: 1" throat compression driver, Magnet: Ferrite | Diaphragm: 1.75", Type: 1" throat coaxial compression driver, Magnet: Ferrite | |
| Amplifier class | Class-D | Class-D | |
| Power rating | Dynamic | 1,000 W (LF: 800 W, HF: 200 W) *1 | 1,000 W (LF: 800 W, HF: 200 W) *1 |
| Continuous | 465 W (LF: 400 W, HF: 65 W) | 465 W (LF: 400 W, HF: 65 W) | |
| Cooling | Fan cooling, 4 speeds | Fan cooling, 4 speeds | |
| Power consumption | 74 W (1/8power), 18 W (Idle) | 74 W (1/8power), 18 W (Idle) | |
| Power requirements | 100 V, 100-120 V, 220-240 V, 110/127/220 V (Brazil), 50/60 Hz | 100 V, 100-120 V, 220-240 V, 110/127/220V (Brazil), 50/60 Hz | |
| A/D D/A Converters | 24 bit 48 kHz Sampling | 24 bit 48 kHz Sampling | |
| Processors | HPF: OFF, 100 Hz, 120 Hz, 24 dB/Oct.; D-CONTOUR: FOH/MAIN, MONITOR, OFF | HPF: OFF, 100 Hz, 120 Hz, 24 dB/Oct.; D-CONTOUR: FOH/MAIN, MONITOR, OFF | |
| I/O connectors | INPUT1: Combo x1, INPUT2: Combo x 1 + RCA pin x 2 (Unbalanced), OUTPUT: XLR3-32 x 1 (CH1 Parallel Through or CH1+CH2 Mix) | INPUT1: Combo x1, INPUT2: Combo x 1 + RCA pin x 2 (Unbalanced), OUTPUT: XLR3-32 x 1 (CH1 Parallel Through or CH1+CH2 Mix) | |
| Cabinet material | Plywood | Plywood | |
| Finish | Durable Polyurea Painting, Black | Durable Polyurea Painting, Black | |
| Handle | Side x2 | Side x1 | |
| Pole socket | Φ35 mm x2 (Bottom, 0° or -7°) | Φ35 mm x1 (Bottom) | |
| Rigging | Top x 2, Rear x 1 (Fit for M10 x 30 - 50 mm Eyebolts) | - | |
| Floor Monitor Angle | - | 57° | |
| Dimensions | W | 432 mm (17.0") | 500 mm (19.7") |
| H | 692 mm (27.2") (with rubber feet) | 343 mm (13.5") (with rubber feet) | |
| D | 405 mm (15.9") | 454 mm (17.9") | |
| Net weight | 24.0 kg (52.9 lbs) | 16.5 kg (36.4 lbs) | |
| Options | - | - |
Get Latest Price
| Rated Power | 15 W |
| Dimension | (L x W x H): 19.25 x 12.67 x 21.65 in (490 x 322 x 550 mm) |
Get Latest Price
| Speaker Type | Coaxial Speakers |
| Type | In-ceiling speakers |
| Speaker Channel | single |
| Frequency Response (- dB) | 96 Hz - 15 kHz |
| Color | Black |
| Output (Peak SPL@M) | 108 dB (low-impedance, 116 dB peak) 106 dB (top 70V/100V tap) |
| Gross Weight | 3.4 kg (7.4 lbs, one speaker) |
| Dim (H x Dia) | 253 mm diameter x 225 mm depth from back of baffle (10.0 in diameter x 8.8 in depth) |
| Sensitivity | 91 dB (1kHz - 16 kHz) |
| Frequency Range (-10dB) | 62 Hz – 20 kHz |
| Power Rating | IEC System Long-Term Ratings (low-Z direct): 100 Watts Continuous Program Power 50 Watts Continuous Pink Noise (200W peak), 100 hr |
| Transformer Taps | 30 W, 15 W, 7.5 W @ 70V or 100V (plus 3.8 W @ 70V only) |
| Frequency Response (±3 dB) | 96 Hz – 15 kHz |
| Sensitivity | 91 dB (1kHz - 16 kHz) |
| Coverage Angle | 110° conical |
| Directivity Factor (Q) | 7.8 |
| Directivity Index (DI) | 8.2 dB |
| Maximum SPL (1m) | 108 dB (low-impedance, 116 dB peak) 106 dB (top 70V/100V tap) |
| Impedance | 8 ohms (in direct/bypass setting) |
| Crossover Network | 12 dB/oct (2nd order) low-pass to LF driver, 12 dB/oct (2nd order) high-pass to HF driver |
| Drivers | LF Driver: 165 mm (6.5 in) HF Driver: 19 mm (3/4 in) |
| Input Connectors | Removable locking 4-pin connector with screw-down terminals. Max wire size 12 AWG (2.5 mm2) |
| Connector Wiring | Pin 1 = + In; Pin 2 = - In; Pin 3 = + Loop Thru; Pin 4 = - Loop Thru |
| Strain Reliefs | Strain relief for two cables or two flex conduits via coupled clamping mechanism |
| Materials | ABS baffle with UL94-V0 and UL94-5VB flame class fire rating; Zinc-plated steel backcan |
| Safety Agency | UL1480, UL2043, NFPA90 & NFPA70; S7232/UL Listed, Suitable for use in air handling spaces, Signaling Speaker; Transformer UL registered per UL1876; ROHS, C-tick N108, CE compliant; Baffle meets UL94-V0 and UL94-5VB flammability rating; In accordance with IEC60849/EN60849 systems |
| Dimensions | 253 mm diameter x 225 mm depth from back of baffle (10.0 in diameter x 8.8 in depth) |
| Ceiling Cutout Size | Circular cutout with 223 mm (8.8 in) diameter (cardboard cutout template included) |
| Ceiling Thickness Range | Up to 38 mm (1.5 in) with stock dog-ears. MTC-TCD thick-ceiling dog-ears available for up to 60 mm (2.4 in) ceiling thicknesses |
| Safety Seismic Attachment | One point, top surface |
| Net Weight | 3.4 kg (7.4 lbs, one speaker) |
| Shipping Weight | 11.2 kg (24.7 lbs, pair in master carton) |
| Included Accessories | C-ring support backing plate, 2 tile support rails (for 2 ft or 600 mm tile spans; optional MTC-48TR extension available for larger 4 ft or 1200 mm tile spans), cutout template, paint shield, removable locking multi-pin connector, grille |
| Optional Accessories | MTC-26NC new construction bracket MTC-26MR mud-ring construction bracket MTC-TCD thick-ceiling dog-ears for ceiling thicknesses up to 60 mm (2.4 in, ordering one set = 24 dog-ears for 6 speakers) MTC-48TR tile rail for 1200 mm (4 ft) tile spans |
| Color | White or Black |
| Backcan | formed steel (included "blind-mount") |
| Baffle/Rim | ABS baffle with UL94-V0 and UL94-5VB flame class fire rating. |
| Plenum Usage | Yes, backcan included |
Get Latest Price
| Connectivity | Wired |
| Frequency Range | 43Hz - 24kHz |
| Dimensions (H x W x D) | 298 x 185 x 231 mm (11.75" x 7.3" x 9.9") |
| Weight | 4.73 kg (10.43 lbs) |
| LF Driver | 126mm (5") |
| HF DRIVER SIZE | 25mm (1") |
| HF DRIVER TYPE | Soft dome |
| Crossover | 1725Hz 4th order acoustic Linkwitz-Riley |
| OK FOR USE NEAR MAGNETICALLY SENSITIVE EQUIPMENT | |
| INPUT SENSITIVITY (-10dBV INPUT) | 92dB / 1m |
| Power Configuration | Bi-amplified |
| HF DRIVER POWER AMP | 41W, Class-D |
| LF Driver Power Handling | 41W, Class-D |
| Frequency Response (±3 dB) | 49Hz – 20kHz |
| Frequency Range (-10dB) | 43Hz – 24kHz |
| LOW FREQUENCY EXTENSION (-10dB) | 43Hz |
| Maximum Continuous SPL | 94dB |
| Maximum Peak SPL | 108dB |
| MAXIMUM PEAK INPUT LEVEL(-10dBV / +4dBu) | +6dBV / +20.3dBu |
| SYSTEM DISTORTION CRITERIA | <10% THD at maximum output with full compressor / limiter engagement |
| ELECTRICAL DISTORTION CRITERIA | 0.2% THD @ 1kHz / 2.83VRMS output; <1% THD @ 1kHz, full rated output |
| Signal to Noise Ratio | 75dBA (A-Weighted), 70dBr (unweighted), relative to 2.83VRMS output |
| Coverage Angle | 120° x 90° |
| Input Connectors | 1 x XLR female, 1 x TRS female, balanced |
| HF TRIM CONTROL | -2dB, 0dB, +2dB |
| BOUNDARY EQ | LF Shelf @ 50Hz: -3dB, -1.5dB, 0dB |
| AC INPUT VOLTAGE | 100 – 240VAC (±10%), 50 / 60Hz |
| ENCLOSURE TYPE | Ported |
| Enclosure | 15mm MDF |
| ENCLOSURE FINISH | Matte black PVC |
| BAFFLE CONSTRUCTION | Injection-molded structural ABS |
| CABINET DIMENSIONS (H x W x D) | 298 x 185 x 231 mm (11.75" x 7.3" x 9.9") |
| DISPLAY CARTON (H x W x D) | 354 x 244 x 299mm (13.9" x 9.6" x 11.8") |
| SHIPPING CARTON (H x W x D) | 373 x 260 x 315mm (14.7" x 10.2" x 12.4") |
| Net Weight (each) | 4.73 kg (10.43 lbs) |
| SHIPPING GROSS WEIGHT | 5.72 kg (12.61 lbs) |
Get Latest Price
| Connectivity | Wired |
| Color | Black |
| Power | 240 W Continuous Program (2 hrs) 120 W (480W peak), Continuous Pink Noise (2 hrs) 90 W (360W peak) C |
| Dimensions (W x D x H) | 386 x 282 x 219 mm (15.2 x 11.1 x 8.6 in); 277 mm (10.9 in) deep total when mounted on InvisiBall wa |
| Impedance | 8 ohms (THRU setting) |
| Sensitivity | 91 dB, 1W/1m (ave. 100 Hz - 10 kHz) |
| Freq.Response | 62Hz - 16 kHz |
| Weight | 6.8 kg (15.0 lbs) |
| Frequency Range (-10dB) | 45 Hz to 20 kHz |
| Frequency Response (±3 dB) | 62Hz - 16 kHz |
| Power Rating | 240 W Continuous Program (2 hrs) 120 W (480W peak), Continuous Pink Noise (2 hrs) 90 W (360W peak) Continuous Pink Noise (100 hrs) |
| Maximum Input Voltage | 27.5 V RMS (2 hrs), 55.0 V peak |
| Maximum SPL (1m) | 112 dB ave. Continuous Pink Noise (118 dB peak) |
| Sensitivity | 91 dB, 1W/1m (ave. 100 Hz – 10 kHz) |
| Coverage Angle | 100°H x 100°V |
| Directivity Factor (Q) | 7.3 (averaged 1kHz – 16kHz) |
| Directivity Index (DI) | 8.3dB (averaged 1kHz – 16kHz) |
| Impedance | 8 ohms (THRU setting) |
| Crossover Type | 2nd order low-pass, 1st order high-pass, plus conjugate shaping |
| Transformer Taps | 70V: 60W, 30W, 15W, 7.5W 100V: 60W, 30W, 15W Insertion Loss: <0.94 dB at any tap setting Thru Setting: 8Ω nominal |
| Recommended ProtectiveHigh-Pass | 45 Hz high-pass (24 dB/oct) for 8Ω operation plus 15W and 7.5W taps; 55 Hz for 30W tap; 65 Hz for 60W tap. |
| Drivers | LF: 200 mm (8 in), woven-fiberglass cone with pure butyl rubber surround with Weather-Edge frame protection, high-temp fiberglass voice coil former, high-temp voice coil wire, optimized cone geometry, linear suspension spider, and FEA optimized motor structure. HF: 25 mm (1 in) PEI diaphragm, low-viscosity ferro-magnetic fluid, and lightweight Kapton™ voice coil former. |
| Enclosure | High Impact Polystyrene (HIPS) with 10% glass fill, painted with highly-UV resistant paint on white (-WH) version for maximum UV fade resistance. |
| Grille | Highly zinc-plated, finished in durable TGIC polyester powdercoating. MTC-28WMG-1 (&-WH) available with WeatherMax™ multi-layer foam and tight-weave mesh vapor barrier backing. |
| Mounting Hardware | InvisiBall wall-mounting system included. Two 6 mm attachment points (on top and bottom) for optional MTC-28WMG-1 (&-WH) U-bracket. Secondary safety attachment loop point on back panel. |
| Outdoor Capability | IP-44 per IEC529 (IP-55 when installed with the optional MTC-28WMG-1 WeatherMax™ grille and either MTC-PC2 or MTC-PC3 panel cover.) Exceeds MilSpec 810 for humidity, salt-spray, temperature & UV. Passes MilStd-202F for salt spray and ASTM G85 for acid-air plus salt spray. Optional MTC-28WMG-1 WeatherMax™ grille for breaking up driving rain and for especially difficult environments. |
| Input Connectors | Screw-down terminal strip, zinc-plated copper based, nickel-plated metal screws and washers. Accepts up to 9 mm outside 4 mm inside open lugs (#6, #8, or #10 lug), plus bare wire (up to 12 AWG / 2.5 mm2). Optional MTC-PC2 and MTC-PC3 protective panel covers available to provide sealed entrance for additional weather protection. |
| Safety Agency | ROHS-compliant; Transformer UL Recognized per UL1876 |
| Colors | Black (RAL9004) or white (-WH, RAL9016) |
| Dimensions (H x W x D) | 386 x 282 x 219 mm (15.2 x 11.1 x 8.6 in); 277 mm (10.9 in) deep total when mounted on InvisiBall wall-mount bracket. |
| Net Weight (each) | 6.8 kg (15.0 lbs) |
| Shipping Weight | 15.4 kg (34 lbs) pair-packed (for 2 speakers) |
| Included Accessories | InvisiBall™ wall-mounting system), 6 mm x 180 mm hex key |
Get Latest Price
| No. of Channels | 4 |
| Impedance | 4 ohm |
| Color | Black |
| Dimension (LxWxH) | 480X88X422 |
| Weight | 8.1kg (17.9lbs) |
Get Latest Price
| Size/Dimension | 432 mm 17.0") 692 mm (27.2") (with rubber feet) 405 mm (15.9") |
| Channel | single |
| Subwoofer Type | Active |
| Color | Black |
| Weight | 24.0 kg (52.9 lbs) |
| DHR15 | DHR12M |
|---|
| DHR15 | DHR12M | ||
|---|---|---|---|
| General specifications | |||
| Speaker type | 2-way, Bi-amped Powered Speaker, Bass-reflex | 2-way, Bi-amped Powered Speaker, Bass-reflex | |
| Frequency range (-10dB) | 44 Hz - 20 kHz | 55 Hz - 20 kHz | |
| Coverage area | H90゚ x V60゚ | H90゚ x V90゚ | |
| Crossover | 1.8 kHz: FIR-X tuning™ (linear phase FIR filter) | 1.8 kHz: FIR-X tuning™ (linear phase FIR filter) | |
| Maximum Output Level (Measured peak, IEC noise@1m) | 131 dB SPL | 129 dB SPL | |
| Components | LF | Diameter: 15" cone, Voice Coil: 2.5", Magnet: Ferrite | Diameter: 12" cone, Voice Coil: 2.5", Magnet: Ferrite |
| HF | Diaphragm: 1.4", Type: 1" throat compression driver, Magnet: Ferrite | Diaphragm: 1.75", Type: 1" throat coaxial compression driver, Magnet: Ferrite | |
| Amplifier class | Class-D | Class-D | |
| Power rating | Dynamic | 1,000 W (LF: 800 W, HF: 200 W) *1 | 1,000 W (LF: 800 W, HF: 200 W) *1 |
| Continuous | 465 W (LF: 400 W, HF: 65 W) | 465 W (LF: 400 W, HF: 65 W) | |
| Cooling | Fan cooling, 4 speeds | Fan cooling, 4 speeds | |
| Power consumption | 74 W (1/8power), 18 W (Idle) | 74 W (1/8power), 18 W (Idle) | |
| Power requirements | 100 V, 100-120 V, 220-240 V, 110/127/220 V (Brazil), 50/60 Hz | 100 V, 100-120 V, 220-240 V, 110/127/220V (Brazil), 50/60 Hz | |
| A/D D/A Converters | 24 bit 48 kHz Sampling | 24 bit 48 kHz Sampling | |
| Processors | HPF: OFF, 100 Hz, 120 Hz, 24 dB/Oct.; D-CONTOUR: FOH/MAIN, MONITOR, OFF | HPF: OFF, 100 Hz, 120 Hz, 24 dB/Oct.; D-CONTOUR: FOH/MAIN, MONITOR, OFF | |
| I/O connectors | INPUT1: Combo x1, INPUT2: Combo x 1 + RCA pin x 2 (Unbalanced), OUTPUT: XLR3-32 x 1 (CH1 Parallel Through or CH1+CH2 Mix) | INPUT1: Combo x1, INPUT2: Combo x 1 + RCA pin x 2 (Unbalanced), OUTPUT: XLR3-32 x 1 (CH1 Parallel Through or CH1+CH2 Mix) | |
| Cabinet material | Plywood | Plywood | |
| Finish | Durable Polyurea Painting, Black | Durable Polyurea Painting, Black | |
| Handle | Side x2 | Side x1 | |
| Pole socket | Φ35 mm x2 (Bottom, 0° or -7°) | Φ35 mm x1 (Bottom) | |
| Rigging | Top x 2, Rear x 1 (Fit for M10 x 30 - 50 mm Eyebolts) | - | |
| Floor Monitor Angle | - | 57° | |
| Dimensions | W | 432 mm (17.0") | 500 mm (19.7") |
| H | 692 mm (27.2") (with rubber feet) | 343 mm (13.5") (with rubber feet) | |
| D | 405 mm (15.9") | 454 mm (17.9") | |
| Net weight | 24.0 kg (52.9 lbs) | 16.5 kg (36.4 lbs) | |
| Options | - | - |
Get Latest Price
| Size/Dimension | 290 x 306 x 351 mm; 11-3/8" x 12" x 13-7/8" |
| Channel | single |
| Subwoofer Type | Active |
| Color | Black |
| Model Name/Number | NS-SW200 |
| Weight | 11.2 kg; 24.7 lbs. |
| Frequency Response | 28-200 Hz |
| NS-SW200 | |
|---|---|
| Subwoofer | |
| Driver | 20 cm (8”) cone |
| Output Power | 130 W |
| Frequency Response | 28–200 Hz |
| Advanced YST | Yes |
| High-Efficiency Power Amplifier | Yes |
| Twisted Flare Port | Yes |
| Auto Standby | Yes |
| Standby Power Consumption | 0.3 W |
| System Connector | Yes |
| Dimensions (W x H x D) | 290 x 306 x 351 mm; 11-3/8” x 12” x 13-7/8” |
| Weight | 11.2 kg; 24.7 lbs. |
Get Latest Price
| Size/Dimension | 350 x 366 x 420 mm; 13-3/4" x 14-3/8" x 16-1/2" |
| Channel | single |
| Subwoofer Type | Active |
| Color | Black |
| Model Name/Number | NS-SW300 |
| Weight | 18 kg; 39.7 lbs. |
| Frequency Response | 20-160 Hz |
| NS-SW300 | |
|---|---|
| Subwoofer | |
| Driver | 25 cm (10”) cone |
| Output Power | 250 W |
| Frequency Response | 20–160 Hz |
| Advanced YST | Yes |
| High-Efficiency Power Amplifier | Yes |
| Twisted Flare Port | Yes |
| BASS (Bass Action Selector System) | Yes |
| Auto Standby | Yes |
| Standby Power Consumption | 0.3 W |
| System Connector | Yes |
| Dimensions (W x H x D) | 350 x 366 x 420 mm; 13-3/4” x 14-3/8” x 16-1/2” |
| Weight | 18 kg; 39.7 lbs. |
Get Latest Price
| Dimensions (W x D x H) | 602 mm x 1067 mm x 838 mm |
Get Latest Price
| Number Of Channels | 2 .0 |
| Available Digital Input Audio format | 40W Program, 150W Peak |
| Dimensions (W x H x D) | 11 x 6.8 x 9.6" |
| Dimensions (H X W X D) | 11 x 6.8 x 9.6" |
Get Latest Price
| Subwoofer Type | Active |
| Size/Dimension | 27 x 30 x 24 inches (685 x 762 x 620 mm) |
| Color | Black |
| Channel | single |
| Rated Impedance | 8 |
| Weight | 100 lbs ( 45 kg) |
| In-room response (2π) | Below 18 Hz |
| Frequency Response, -10 dB (4π measurement) | 20.6 Hz |
| Frequency Response, -6 dB (4π measurement) | 23.1 Hz |
| Maximum Peak SPL | 137 dB SPL |
| System Input Power Rating, AES/2 Hr.: | LF 2000W continuous/8000W peak |
| Sensitivity | 92dB @ 1m, 2.83 V |
| Amplifier Power Rating | 3,500 to 4,000W into 8Ω |
| Recommended Signal Processing | Crown iTech HD Power Amplification. Preset for use with JBL M2 available |
| LF Driver | One JBL model 2269H, 18-inch (457 mm); 100mm (4-inch) dual voice coils, dual neodymium magnets. Differential Drive® Direct Cooled™ |
| Rated Impedance | 8Ω |
| Enclosure | 18mm 11-ply Baltic Birch Plywood |
| Finish | Black Lacquer |
| Input Connectors | 2 ea. Push Terminals |
| Recommended Wire | 12-Gauge |
| Dimensions HxWxD (including feet) | 27 x 30 x 24 inches (685 x 762 x 620 mm) |
| Net Weight (each) | 100 lbs ( 45 kg) |
| Frequency Response (±3 dB) | 18 Hz @ 2π |
Get Latest Price
| Brand | Behringer |
| Type | Digital |
| Usage/Application | XLR |
| Model Name/Number | X AIR XR 18 |
| Color | Black |
The Behringer X32 completely changed the game by rethinking what is possible from a digital mixer – and over 100,000 users are enjoying the results. Now, that same technology has been incorporated into a small, but incredibly powerful, rack-mountable mixer that will forever change both the way you record – and the way you play live music.
The revolutionary XR18 is a powerhouse 18 input/12 bus portable mixer housed in an extremely sturdy stage box design for use with iPad and Android tablets. It is ideally suited for both live and studio applications, thanks to its 16 award-winning Midas-designed mic preamps, convenient integrated WiFi module for wireless control – and a lightning-fast, bidirectional USB Audio Interface.
Get Latest Price
| Color | Black |
| Dimensions (H x W x D) | 485mm x 725mm x 585mm |
| Weight | 37.5kg |
| MODEL NAME / NO | CORE 151 |
SUB SPECIFICATION:
Speaker – 1×15” low frequency driver
Rated power (SUB) – 700W (rms)
Amplifier power – 700W (LF) + 400W (MF/HF) (rms)
Max SPL – 128dB
Dimensions – 485mm x 725mm x 585mm
Net weight – 37.5kg
CURVE ARRAY SPECIFICATION:
Speaker MF – 3×8” Neodymium full range driver
Speaker HF – 12×1” dome tweeter
Rated power – 400W
Coverage – 100° (h) x 70° (v)
Dimensions – 255mm x 670mm x 285mm (450mm max)
Net weight – 11.5kg
MIXER SPECIFICATION:
DSP – 24bit module with mode, EQ, limiter, delay and mix level control
Inputs – 2x mic (XLR) / line (6.35mm jack) balanced, 1x instrument Hi-Z (6.35mm jack), 1x stereo line (RCA phono) / Bluetooth®
Outputs – 2x balanced line / link output (XLR), 1x balanced line / link MIX output (XLR)
Get Latest Price
Get Latest Price
Get Latest Price
18 Input Mixer (16 Mic / Line + 1 Stereo Input).
6 AUX Channels (4 pre, 2 post).
Provision on board to route EFX to monitors (via AUX 3 & AUX 4).
4 Sub Group with individual outputs.
Split global Phantom power from 1-8 & 9-16.
Mono sub output with low frequency selection.
3-band EQ with Mid-sweep on mono inputs.
3-band EQ on stereo inputs.
Inserts on mono channel.
Mix & Group Routing on each channel.
Stereo AUX Return.
100mm faders.
PFL switch on each channel.
100Hz Low cut on each mono channels.
Peak & Mute LED per channel.
12 V Lamp Socket.
Balanced XLR & Jack main outputs
Get Latest Price
Get Latest Price
| Color | Black |
| Brand | JBL |
| Frequency Range (±3 dB) | 70 Hz – 20 kHz |
| Frequency Range (-10dB) | 55 Hz – 20 kHz |
| Coverage Pattern | 100° x 100° |
| Directivity Factor (Q) | 10.1 (1 k – 16 kHz) |
| Directivity Index (DI) | 9.5 dB (1k – 16 kHz) |
| Power Rating | 400 W (1600 W peak), 2 hrs. 250 W (1000 W peak), 100 hrs |
| Sensitivity | 96 dB (Ave. 70 Hz – 20 kHz) |
| Maximum SPL (1m) | 122dB (peaks of 128 dB) |
| Crossover Network | 1.8 kHz, 3rd order (18 dB/oct) high-pass plus conjugate to HF, 2nd order low-pass to LF |
| Nominal Impedance | 8Ω |
| LF Driver | Kevlar-reinforced cone, 75 mm (3 in) voice coil. |
| HF Driver | 25 mm (1 in) diaphragm and voice coil diameter, high temperature polymer diaphragm, patented design, fluidcooling. |
| HF Driver Protection | Minimum audibility SonicGuard™ HF overload protection |
| Enclosure | ABS with Glass enclosure, heavily braced |
| Attachment | Two M10 points for included U-bracket. M6 secondary safety attachment point on back panel. |
| Grille | Corrosion-resistant zinc-rich steel grille. |
| Dimensions | 402 x 402 x 445 mm (15.8 x 15.8 x 17.5 in), cabinet 470 mm (18.5 in) depth with gland nut 502 mm (19.75 in) including bracket extending to back |
| Colors | Black |
| Net Weight (each) | 14.0 kg (31.0 lb), 16.8 kg (37.0 lb) with U-Bracket |
| Shipping Weight | 19.5 kg (43.0 lb) |
| Included Accessories | U-bracket, Steel |
| Horizontal Coverage Angle (-6dB) | 100° |
| Vertical Coverage Angle (-6dB) | 100° |
| Power Handling (2Hr AES Rating) | 400 W |
Get Latest Price
| Channel | single |
| Subwoofer Type | Passive |
| Color | Black |
| Rated Impedance | 8 ohms |
| Weight | 9.4 kg (20.7 lbs) |
| CBR12 | CBR10 |
|---|
| CBR12 | CBR10 | ||
|---|---|---|---|
| General specifications | |||
| Speaker type | 2-way Speaker, Bass-reflex Type | 2-way Speaker, Bass-reflex Type | |
| Frequency range (-10dB) | 48 Hz - 20 kHz | 50 Hz - 20 kHz | |
| Nominal coverage | H | 90° | 90° |
| V | 60° | 60° | |
| Components | LF | 12" Cone, 2" Voice Coil (Ferrite Magnet) | 10" Cone, 2" Voice Coil (Ferrite Magnet) |
| HF | 1.4" Voice Coil, Compression Driver (Ferrite Magnet) | 1" Voice Coil, Compression Driver (Ferrite Magnet) | |
| Crossover | 2.1 kHz | 2.8 kHz | |
| Power rating | NOISE | 175W | 175W |
| PGM | 350W | 350W | |
| PEAK | 700W | 700W | |
| Nominal impedance | 8Ω | 8Ω | |
| SPL | Sensitivity (1W; 1m on axis) | 96dB SPL | 94dB SPL |
| Peak (Calculated) | 125 dB SPL | 123 dB SPL | |
| I/O connectors | 1/4" Phone x 1, speakON NL4MP x 1 | 1/4" Phone x 1, speakON NL4MP x 1 | |
| Cabinet material | Plastic | Plastic | |
| Finish | Black | Black | |
| Handle | Side x 2 | Top x 1 | |
| Flying and mounting hardware | Bottom x 2, Rear x 1 (Fit for M8 x 15mm Eyebolts) | Bottom x 2, Rear x 1 (Fit for M8 x 15mm Eyebolts) | |
| Pole socket | Φ35 mm Bottom x 1 | Φ35 mm Bottom x 1 | |
| Dimensions | W | 376mm (14.8") | 308mm (12.1") |
| H | 601mm (23.7") | 493mm (19.4") | |
| D | 348mm (13.7") | 289mm (11.4") | |
| Net weight | 13.9 kg (30.6 lbs) | 9.4 kg (20.7 lbs) | |
| Accessories | Optional Speaker Bracket: BBS251, BCS251, BWS251-300, BWS251-400 | Optional Speaker Bracket: BBS251, BCS251, BWS251-300, BWS251-400 |
Get Latest Price
| Dimensions (W x D x H) | 629 mm x 432 mm x 324 mm |
The VRX915M is a dedicated, compact and lightweight, 15", two way touring-class floor monitor, with only a 375 mm (14.75 in) stage height and JBL’s latest neodymium-magnet transducers. A 380 mm (15 in) 2265H patented Differential Drive® woofer handles 800 watts (continuous) and delivers accurate and precise low frequency reproduction. The 2452H 102 mm (4 in) voice-coil compression driver is coupled to a 50° x 90° aluminum horn to provide smooth and clear high frequency reproduction, critical for high performance monitoring. Bi-amp or full-range passive operation may be selected via a recessed, high-current switch mounted alongside the NL4 input connector in one of the handle cups. An additional NL4 connector is mounted in the other handle cup for a convenient loop-thru connection, minimizing cable runs on stage. The enclosure is constructed of top quality Baltic birch plywood and is coated in JBL’s rugged DuraFlex™ finish. It is a symmetrical 30° wedge design, with four non-slip rubber feet per side enabling convenient left and right applications of adjacent monitors. The transducers are protected by an attractive 16 gauge CNC-machined steel grille, which is internally lined with acoustically transparent foam to provide additional transducer protection.
Get Latest Price
| Connectivity | Wired |
| Subwoofer Size | 15 Inch |
| Speaker Channel | single |
The JBL IRX115S powered subwoofer, the newest model in the IRX series of versatile, cost-conscious portable PAs, extends the low-frequency response of IRX systems down to a room-shaking 35 Hz.
The 15” IRX115S draws from JBL’s top professional touring technologies to deliver superior sound without the guesswork, thanks to the custom driver and amplifier designs; tuned, ported enclosure; and built-in crossover and polarity settings. It all adds up to an impressive 128 dB of deep, powerful bass in a rugged, ultralight cabinet weighing just 65.3 pounds.
The IRX Series offers legendary JBL fidelity, power, and ease of use at a fraction of the price and size of comparable systems. The 8-inch IRX108BT and the 12-inch IRX112BT are fully loaded with features that make it easy to dial in incredible sound instantly—from real-world EQ presets and dbx DriveRack automatic feedback suppression to Bluetooth streaming and one-touch ducking.
Budget-conscious musicians, DJs, presenters, and fitness instructors can count on versatile, full-featured JBL IRX Series portable PAs to deliver stunning sound, no matter their experience level.
Get Latest Price
| Brand | Behringer |
| Type | Digital |
| Channel | 12 |
| Usage/Application | Multipurpose |
| Model Name/Number | X Air XR12 |
| Audio Interface | Yes |
The BEHRINGER X32 completely changed the game by rethinking what is possible from a digital mixer – and over 100,000 users are enjoying the results. Now, that same incredible technology has been incorporated into a small, but incredibly powerful, rack-mountable mixer that will forever change both the way you record – and the way you play live music.
The revolutionary XR12 is a powerhouse 12 input portable/rack-mountable mixer for iPad and Android tablets, and is ideally suited for both live and studio applications, thanks to its 4 award-winning MIDAS-designed mic preamps, convenient integrated WiFi module for wireless control, plus USB connectivity for file storage, system updates and uncompressed stereo recordings via the USB Stereo Recorder. We’ve also included the rack ears and protective bumpers for added flexibility in your studio and stage applications.
The freedom to move around and manipulate all parameters of your mix with the free iOS and PC apps lets you dial in the perfect sound from anywhere in the venue – or the tracking room! Advanced engineering and meticulous design deliver stellar sonic performance at an extremely affordable price – changing the game once again.
Get Latest Price
| Power | 300 W |
| No. of Channels | 2 |
| Impedance | 8 ohm |
| Connectivity | Speakon |
| Damping Factor | 200 |
| Color | Black |
| Dimension (LxWxH) | 89 X 483 X 360 |
| Weight | 16 Kgs |
Get Latest Price
| Brand | Studiomaster |
| Model Name/Number | Digitrack 18 |
| Color | Black |
Get Latest Price
Get Latest Price
| Usage/ Application | INDOOR SPEAKER |
| Brand | Ahuja |
| Color | WHITE |
| Dimension | W262 x H262 x D128 mm |
PA Wall Speaker
High quality ABS wall mounting box speaker for indoors; speech & background music. For Schools, Offices, BPOs, Hospitals, Banks, Restaurants, Showrooms and Hotels.
|
Input Power |
6W RMS |
|
Power Taps on 100V |
6/3/1.5W |
|
Impedance |
1.6k/3.3k/6.6kΩ |
|
Frequency Response |
60-15,000Hz |
|
SPL at 1kHz (1W/1m) |
92dB |
|
Dimensions |
W262 × H262 × D128 mm |
|
Weight |
1.50kg |
₹ 72000 / Piece Get Latest Price
| Model Name/Number | R400C |
| Power | 20-200W |
| Dimensions | 24.2 x 7.8 x 13.8 |
| Feature | Home Theater Essential: The center channel speaker is the most important speaker in your home theate |
| Frequency Range | 36Hz - 50kHz |
| Weight | 32.8 lbs/14.9 kg |
| Color | Black |
₹ 39990 / Piece Get Latest Price
| Amplifier Output Power | 40W, Class AB amplification |
| Brand | Presonus |
| Color | Black |
| Frequency Range | 35 Hz to 20 kHz |
Listen to your mixes reproduced with lifelike realism! The Eris® Pro 8's symmetric design and consistent acoustic center provides superior phase alignment between components to deliver a wide sweet spot, precise stereo imaging, and symmetrical dispersion patterns, making them ideally suited for immersive Dolby Atmos rooms and stereo mix environments alike.
The Eris Pro 8's coaxial design provides a single acoustic point source that creates a natural listening experience, revealing the subtlest nuances in your recordings, while providing a three-dimensional soundstage, detailed transient response, and lifelike sonic reproduction. Combined with a punchy low-end that defies its compact size, the Eris Pro 8 provides a superior listening experience for both home studios and professional mix rooms.
A 1.25-inch, ultra-low mass, silk-dome tweeter ensures snappy, accurate transient reproduction, while a 8-inch, woven-composite woofer offers tight, clear bass, with plenty of punch and no flab. A ported enclosure and 140 watts of power allows the Eris Pro 8 to reach down to an astonishing 35 Hz, while a finely detailed transient response and stunning dynamics deliver a natural and less fatiguing experience.
Acoustic tuning controls and a three-way Acoustic Space tuning lets you accurately configure the Eris Pro 8 for your room. Flexible input options enable connection to almost any line-level source, from mixers to audio interfaces and more. Provisions for wall and ceiling mounts make it easy to integrate Eris Pro 8 monitors into any stereo or multi-channel system.
Get Latest Price
| Subwoofer Type | Active |
| Size/Dimension | W 300mm (11.8") H 350mm (13.8") D 389mm (15.3") |
| Color | Black |
| Channel | single |
| Power | 150 W |
| Weight | 12.5kg (27.6 lbs.) |
|
|||||||||||||||||||||||||||||
Country of origin: Indonesia
Importer Details: P 401, JMD Megapolis, Sohna Rd, Sector 48, Gurugram, Haryana 122018
Get Latest Price
| Connectivity | Wired |
| Type | In-wall speakers |
| Power | 200 W Peak 100 W Continuous Program Power 50W Continuous Pink Noise |
| Color | White |
| Impedance | 8 ohms |
| Sensitivity | 90 dB SPL |
| Freq.Response | 38 Hz - 20 kHz (-10 dB) |
| Weight | 2.6 kg (5.5 lb) |
| Frequency Range | 38 Hz - 20 kHz (-10 dB) |
| Power Rating | 200 W Peak 100 W Continuous Program Power 50W Continuous Pink Noise |
| Sensitivity | 90 dB SPL |
| Coverage Angle | 180°H x 160°V |
| Impedance | 8 ohms |
| Drivers | LF: 200 mm (8 in) polymer-coated aluminum cone, pure butyl rubber surround. HF: 25 mm (1 in) pure-titanium dome with cloth suspension on low-diffraction swivel-mount with -10 degree aimability. |
| Input Connectors | Screw-down Euroblock-type connector. Max wire size 14 AWG (1.5 mm)2 |
| Crossover Network | 2nd order Low Pass to the woofer and 2nd order High Pass to the tweeter. |
| Optimum Air Cavity Behind Speaker | 40 to 80 liters (1.4 to 2.8 cu ft) |
| Outside Dimensions (H x W x D) | 334 x 257 x 110 mm (13.1 x 10.1 x 4.3 in), 102 mm (4.0 in) front of wall to back of speaker. |
| Maximum Wall Thickness | 32 mm (1.25 in) |
| Cutout Size (H x W) | 300 x 225 mm (11.9 x 8.9 in), Cutout template included. |
| Net Weight (each) | 2.6 kg (5.5 lb) |
| Shipping Weight (ea) | 128 W: 5.9 kg (13.0 lb) |
| Included Accessories | Cutout template & paint shield |
| Optional Accessories | WB8 Rough-In Frame for newconstruction installation to wallstuds |
Kangayan Singaram (Managing Director)
Studio Care Private Limited
Ground Floor, No.108, Singaram Saraswathi Illam, 14th Street, M.G. Chakrapani Nagar, Alapakkam
Chennai - 600116, Tamil Nadu, India